Categories
Uncategorized

French Drains: Interior French Drains vs Exterior French Drains – What Is The Best?

Basements are among the most vulnerable areas in a home. They are below the ground’s surface. In some states, building codes require the installation of exterior or inside French drains.

These systems offer the best chance to prevent flooding, water damage and mold growth in basements. How can you choose the right system for your home? Here are the facts.

Exterior French Drains

French drains can be installed around foundation perimeters. The drain is a flexible perforated drainpipe that is buried in the foundation footing. To filter dirt and sediments, landscape fiber and gravel are placed around the pipe.

Water that pools around foundation walls will enter the pipe and drain away to a sump pump within the house.

Exterior drain installation is more difficult because it involves the removal and replacement of landscaping, driveways sidewalks porches decks, porches, porches, walkways, decks, and other elements. Maintenance is also difficult and expensive, which can lead to costly exterior excavation. Because the pipe is buried under several feet of soil, it can become clogged over time.

Interior French Drains

A perforated pipe is also used to create an interior French drain. It’s located around the perimeter of the basement floor. The gravel surrounding the perforated pipe filters out dirt and sediments, just like exterior drains. As it enters the basement, the pipe collects water and transports it to a sump pit. There, a pump pumps it away from the foundation.

Interior drains can be installed in existing homes without causing disruption or requiring as much labor as exterior drains. The preparation involves removing all belongings from the basement walls and using a Jackhammer to break down concrete.

Because the pipe is easily accessible, interior drain maintenance is much easier. The pipe is also less likely to become clogged because it’s not hidden under several feet of dirt. Interior systems are also protected against the elements, soil conditions and roots that may grow into the drainage system. They can also be installed all year round, regardless of the season.

Conclusion

French drains can be installed in both the exterior and interior of your basement to protect it from flooding or water damage. However, because of the difficulty and cost of servicing and installing an exterior drain on an existing house, it might be cheaper to install interior drains. Note: If you are building a new house, make sure to check your local building codes. To determine the best drainage system for your home, consult a basement waterproofing specialist.

Categories
Uncategorized

Roof Leak: What To Do When You Get A Roof Leak?

Roofs can become weaker over time due to exposure to the elements. This makes roof leaks almost inevitable. If they aren’t repaired within 24 to 48 hour of water intrusion, leaking roofs can lead to water damage, or mold growth.

Tips To Help Mitigate Roof Leaks

Minimize interior water damage

  • Any items that are susceptible to water damage, such as valuables, electronics and furniture, should be moved to dry areas. If furniture is not possible to move, cover it with plastic sheets.
  • To collect water, place a bucket underneath the leak. To stop water from splashing onto the floor and into the bucket, attach a piece string to the ceiling.
  • Leakage of water can cause ceiling paint to bubble up or blister. To release water from the ceiling, use a pin to puncture the paint with a small needle.

Find and fix the leak

  • To locate the source of the leak, you can trace the water path through your attic if you have access. You should look for moisture-related watermarks, stains, or discolorations in the wood.
  • The point at which water is leaking into your interior may not be the exact location of the crack in your roof. Water can travel down beams and trusses from the entry point to the roof, until it reaches a weak spot in the attic floor. This could cause a leak.
  • You should be aware of the various causes of leaky roofs.
  • To prevent roof leaks or structural water damage, have your gutters and downspouts checked twice a year.
  • If you don’t feel confident performing the tasks, contact a professional roofing company.
Categories
Uncategorized

Dry Out Walls After Water Damage? – Guide

After an event that causes water damage in your home, not only would the floors be affected, but often the walls are as well. Thus, it’s essential to know how to dry wet walls—or call a restoration company immediately. Quick drying reduces the risk of structural damage and prevents mold from growing.

Understanding how water saturates drywall 

Before you learn how to dry a wall after water damage, here’s a look into how water saturates drywall. Water that enters a room from ground level will cover the floor and floor covering. It will then begin to “wick” up the wall because of capillary action in porous materials. The extent of this movement depends on the wall’s construction, the amount of water, and the water’s height on the wall material.

Drywall is an absorbent material that contains gypsum and a cardboard-like paper on both sides. Drywall can wick water up to 30 inches! The water will be present on both sides of the wall. Often, however, it’s higher on the inside due to restricted evaporation on that side of the drywall. While water damage is sometimes visible, at other times, the wall does not show signs of this moisture.

How to dry a wall after water damage

To begin with, decide whether to handle the problem yourself or call a professional company. We recommend the latter if you don’t know how to dry wet walls or the damage is extensive.

If you want to DIY, here’s how to dry wet walls out: 

If a burst pipe led to the water intrusion, turn off the water source. Hire a plumber to fix the broken pipe before any drying can take place.

Accelerate drying by opening windows and doors. Use fans to move air around the damp walls. Dehumidifiers can help remove moisture from the air, which indirectly removes it from the walls, too.

To speed up evaporation, remove molding and baseboards to prevent moisture from entering behind them. Store the molding in a dry, safe place to avoid damaging it. Also, remove objects hanging on the wall, such as paintings and portraits.

Remove wallpaper if you have it. This takes patience, but it’s important as the wallpaper forms a “seal” that holds moisture in the wall. Wallpaper removal solutions, which dissolve the adhesive, are available at your hardware store. You will also need 3”-6” broad knives to scrape the wallpaper once released.

Note that fully drying out walls takes time, so don’t rush the refinishing until the walls are dry. A moisture meter can help you be sure. Once completely dry, you can reverse the process and refinish your room. Inspect the removed items for any moisture or mold growth before reinstalling.

Drying wet walls quickly and correctly is crucial. If you can’t dry your walls immediately, don’t let the problem get worse by waiting. Call a water damage remediation specialist and leverage their expertise, experience, and equipment.

How restoration professionals dry damp walls after water damage

First, technicians determine the extent of the water using a range of water damage restoration tools. One choice is a non-invasive moisture meter. This meter uses radio waves to test for water without putting holes in the wall.

Another professional instrument is an infrared imaging (IR) camera. Since the evaporation from wet walls makes them cooler than dry walls, the IR camera can find water in walls. It does so with no holes or other invasions of the wall material.

Once the professionals identify wet walls, they use specialized drying equipment to dry them.

If the walls aren’t insulated: 

In this case, the restoration professional can dry wet walls out without holes or removing the baseboard. The technicians place high capacity air movers along the wall every 10 to 14 feet. These air movers remove moisture from wall’s surface, evaporating it quickly. As the moisture evaporates, more moisture goes to the surface where it evaporates.

The restoration expert will also install a low grain refrigerant dehumidifier in the damp wall. Depending on the moisture levels, one or more will be needed. This advanced drying equipment reduces the humidity levels to help with drying and prevent mold growth.

When proper, the restoration professional will install an inner-wall drying system by putting small holes above the sill plate and forcing air into the wall cavity. Studies have shown that this solution is the best and fastest way to dry walls with water damage.

Additionally, if there‘s a moisture barrier on the outside or inside the wall, the drying plan changes. Moisture barriers are coatings or materials that inhibit the movement of moisture from the wall material.

Most latex paints are permeable and don’t make up a barrier. But, glossy paints may create a barrier and enamel paint or vinyl wall coverings create a complete barrier. Technicians will need to perforate or remove them to allow moisture to escape and the walls to dry. If there’s plastic or foil on the inside of the wall, then technicians will need to remove the wall. That’s because drying will not occur properly and mold will develop in such situations.

If the walls are insulated:

If there is fiberglass insulation with paper backing, then an inner-wall drying system can be used, as described above. But, if the insulation is foil-backed fiberglass, blown-in cellulose, or a Styrofoam material, then it can’t be dried successfully.

In those cases, removing the damaged portion of the wall along with the insulation is necessary to allow rapid drying and to prevent mold growth.

Monitoring the drying system 

Regardless of the procedures used by the restoration professional, homeowners should know that the equipment must operate, without stopping, throughout the drying process.

Finally, restoration professionals will monitor the drying system at least once a day. That ensures the equipment is operating correctly during the drying process. Monitoring includes moisture measurements to determine when the materials will successfully dry. Material dryness is measured against similar unaffected contents in that structure. When dryness levels are equal, the drying is finished, and the equipment removed.

To recap, this is how to dry out damp walls

  1. After addressing the water source, remove paintings and other objects from the wall.
  2. Follow up by removing moldings, baseboards, and wallpaper.
  3. Open windows and doors to help speed up the drying process.
  4. Use fans to move air around the damp walls. Also use dehumidifiers, which can help remove moisture from the air and walls.
  5. Professionals use tools like moisture meters, infrared imaging devices, dehumidifiers and heavy-duty fans. That ensures the walls are truly dry before further repair, painting or refinishing.
Categories
Uncategorized

Safety Tips For Space Heaters

People across the country take steps to keep their loved ones warm during winter as outdoor temperatures drop. We now have to address the problem of fires involving heating equipment. It is important to learn space heater safety tips. These are disturbing statistics from National Fire Protection Association (NFPA).

Space heaters use a lot of electricity to produce heat. Space heaters pose a risk of fire and should be avoided. Keep these safety tips in mind when using space heaters.

Safety tips for space heaters

  • Look for one that has the label of a nationally-recognized testing laboratory. These heaters have been evaluated to ensure they meet safety standards. Manufacturers are required to give important care and use information to consumers.
  • A heater should have a guard surrounding the heating element. Protect your skin and fabrics by using a wire grill or another protection to protect the heating element. However, portable electric heaters heat by circulating water or oil and do not require guards.
  • Read the instruction manual before you use a heater. Follow the instructions to operate and maintain your heater.
  • You must ensure that the heater, plug, cord, and outlet are in good condition. Cords should not be run under carpets or rugs as they can cause damage and even a fire.
  • To power heaters, never use extension cords or power strips. The devices should be plugged directly into wall outlets. To reduce overheating, don’t plug in any other electrical devices into the same outlet.
  • Make sure the plug, cord, and outlet are not too hot. If the heater’s wires are too hot, immediately unplug it and get it checked by a professional.
  • Ensure that you are always in control of the heaters when they are being used. Unplug them before leaving the room or going to bed. The portable electric air heaters can only be used temporarily to provide supplemental heating.
  • Heaters should be kept at least three feet from flame-prone materials such as paper, carpet, and trash bins.
  • Although electric space heaters don’t have an open flame the heating elements of certain electric heaters can ignite nearby combustibles. You should also check the temperature of objects around you to make sure they are not too hot.
  • You shouldn’t dry your clothes with an electric heater.
  • You should place heaters on a horizontal, stable surface, preferably the floor, so that they are not easily knocked over.
  • To prevent heater damage, heaters should not be used in areas with high humidity, such as the bathroom and kitchen. To reduce the chance of electric shock, never touch the heater with wet hands.
  • Children and pets should always be supervised when the heater is on. You should not place the heater in a location where children could play or people might bump into it. Children should not be allowed to adjust or move the heater.
  • The heater should be kept in a safe and working condition. Replacing guards or controls should be done immediately. Never operate a defective heater.
Categories
Uncategorized

How To Remove Cigarette Smoke Odor? – Solution

Many years of smoking can cause a home’s walls and contents to become stained and emit foul odors. Professional cigarette smoke odor removal may be necessary. Find out more about cleaning homes affected with tobacco residue and odors.

What’s cigarette smoke?

Cigarette smoke residue, a yellowish-brown gluey substance, sticks to any surface in a house, making it difficult and costly to clean up.

The environmental tobacco smoke (ETS), which results from the burning of cigarettes, pipes, and cigars, is also known as “secondhand smoking.” It contains over 7,000 compounds, of which more than 40 are linked to cancer according to the Environmental Protection Agency. ETS is often called “passive smoking” and can affect both smokers as well as non-smokers.

How does smoking affect your home?

The effects of smoking are not limited to the individuals who have been exposed. It also creates odorous substances that stick on every surface where it has occurred. Smoking can cause yellowish-brown stains to be permanently removed by binding to walls, furniture, or plastics. The odor-absorbing properties of cigarettes are also penetrated by cigar smoke, including carpets, upholstery and bedding, as well as clothes.

The HVAC system in a building can also carry the smoke odor and chemicals throughout. These odors can cause skin irritation and may make surfaces unattractive. Long-term smoking in enclosed spaces can lead to the same results as a fire. Tobacco smoke chemicals can be more difficult to get rid of than those from a fire.

Tobacco residue can be difficult to remove. Professional equipment and services are required. Here are some tips to get rid of cigarette smoke odors.

Home Odor Reduction from Cigarette Smoke

Solutions to remove cigarette odors over the long-term

You must clean every corner and surface of your home to remove the cigarette smoke smell.

  • To let in as much fresh air as possible, first open all windows and doors.
  • Replace, clean, or replace your furnace filters, air filters, and AC filters.
  • Use products with ammonia or glycol to clean walls and ceilings. These ingredients can neutralize unpleasant odors. Allow the walls to dry, and then check for any lingering odors.
  • You can still smell the cigarette odor if you have cleaned your walls and ceilings. Before painting, use a sealant that will lock in odors.
  • All surfaces in your home should be cleaned: windows, floors, carpets and furniture. If the tobacco smoke is difficult to remove, you can hire a professional cleaner.

Solutions to remove cigarette odors temporarily

These are some tips for short-term, inexpensive solutions:

  • You can use an air purifier to clean your home.
  • Sprinkle baking soda on your carpets and allow it to sit overnight for bad odors to be absorbed. Vacuum it the next morning.
  • To neutralize the smell, place saucers of white wine around the house.
  • Indoor plants can absorb up 87% of indoor pollutants
  • You can place small cups of coffee around the house.
  • You can use scented or unscented candles.
  • Orange peels can be left around the house.
  • For 24 hours, place pineapple slices in the room. Keep all doors and windows locked.
  • You can place bowls of activated carbon around your home.

It can be difficult and time-consuming to completely remove the cigarette smoke smell from your home. 

How professional remove smoke odor from property

It is difficult to remove tobacco residue from the affected areas. There is no magic solution that will remove all traces and smells.

Air fresheners are temporary and can cause health problems. The odor will not be completely eliminated if you cover it with paint, even if you haven’t cleaned the room first. The smoke residue can seep through the paint and spread offensive odors throughout the room within weeks to months.

Clean and seal all structural surfaces is the best way to get rid of tobacco smell and residue. Tobacco smoke removal begins with cleaning all surfaces. To help remove the very small particles of tobacco smoke, every cleanup includes deodorizing agents.

After technicians have cleaned the visible surfaces, specialized equipment may be necessary to remove any odors that aren’t easily accessible (such as those in walls and joints). The professional equipment used to remove the smelly particles from the difficult-to-reach places will be hydroxyl and ozone generators.

Next, seal the surfaces with a sealing agent. You will need a product that seals smoke residues. These products can seal in all traces of stains and odors. The surfaces are now ready for painting, refinishing, or applying new covers.

What about soft things? Soft items, like upholstery, bedding, draperies and clothes absorb odors well and can be easily damaged. They are difficult to restore and may require specialist help. These items and materials are often replaced.

Categories
Uncategorized

Why Is Fire & Smoke Alarm Randomly Going Off? – Solution

Smoke alarms can be very important to keep you and your family safe from a house fire. They don’t always sound if there is a fire in your home. Fake alarms are not uncommon, but you shouldn’t ignore them if there is no smoke or visible signs of fire. Hidden fires such as electrical ones can be detected by smoke detectors before you can. When an alarm sounds, assume that there is a fire. Follow safety precautions. Here are some top causes of false smoke alarms to help you understand the workings of smoke alarms.

Ten Reasons Your Smoke & Fire Alarm Doesn’t Stop Working

  • Antifreeze

Smoke alarms can be activated if you aren’t watching the stove while cooking. Sometimes smoke is not necessary. A hint of burned food can trigger the detector. Make sure that your smoke alarm is placed in a safe place, such as in the hallway leading into the kitchen and not in the actual kitchen.

  • Popcorn or Burnt Toast

It can be dangerous to leave bread in the oven or microwave popcorn in the microwave for too long. This can cause heavy particles to be released into the atmosphere, which is what your smoke alarm detects. Keep your smoke detector away from any other devices to avoid such an unfortunate situation.

  • Fireplaces

Smoke detector false alarms can also be caused by fireplaces. Smoke from a fireplace can cause an alarm to go off. However, this is not the alarm’s fault. The dampers and chimney might not be set correctly. If your fireplace emits smoke, you should hire a chimney sweep.

  • Ammonia

False alarms can be triggered by dense water vapor, which is similar to humidity. Smoke detectors will sound an alarm if you use the stove to boil water or take a hot shower. To prevent this, make sure to ventilate your kitchen and bathroom.

  • Chemical Smells

Smoke detector false alarms can also be caused by painting or the use of harsh chemicals. These chemical odors are picked up quickly by smoke detectors. To avoid the alarm’s startling sound, ventilate areas where you use chemicals or paint.

  • Low Battery Charge

Smoke alarm batteries that aren’t properly connected or running low often make small chirping sounds. Although it is not smoke detection, this is a sign to make sure your device is working properly. You should replace your batteries at least twice per year, when daylight savings time ends and begins.

  • Alarm for Old Smoke

Smoke alarms have a life expectancy of approximately 10 years. Smoke alarms can give off false alarms when they reach the end. Replace your detector immediately if it is more than 10 years old.

For fire damage restoration

Smoke alarms are sensitive. A false alarm does not necessarily mean that the detector is dead. They are there to catch fires before they become dangerous. Your smoke alarms should not be too close to potential fire hazards, but they should not be too far away.

The smoke damage caused by the smoke alarm did not cause an alarm in the unfortunate event that it didn’t. Professional disaster restoration professionals will be needed to deal with the smoke and fire damage.

Categories
Uncategorized

Water Damage Restoration In Las Vegas

Disasters such a fire, water, or mold infestation can all happen. Las Vegas’s business and residents need to hire a top-tier cleanup and reconstruction company. The best Las Vegas water restoration companies are available 24 hours a week, and can be reached within hours. Las Vegas water damage specialists are always on hand to respond to any kind of disaster.

The best water restoration Las Vegas services have years of experience and can deal with any time of restoration project. It is very difficult to determine the mold extent in different areas of a damaged structure during Las Vegas water damage restoration. Mold testing, mold spore elimination, and confirming that the air is clean and healthy are all services that are offered by Las Vegas water restoration companies. 

The best water damage restoration in Las Vegas companies provide services at all hours of the day, including weekends, weekdays and holidays. The water damage Las Vegas professionals can help you at any hour of the day or night. They are ready and available to respond to any type of disaster.

The best Las Vegas water damage restoration companies provide local service, which is 365 days a Year and 24 hours per day. When you need their assistance, just give them a call.

Categories
Uncategorized

How To Remove Moldy Smell From Carpet

We heard that your hometown was hit by a flood. We are all familiar with how messy and disgusting things can become. Moldy odors make it difficult to invite guests to your home. It is impossible to completely remove the carpet from your home, but you can call a flood carpet cleaning company. These companies use commercial fans and special equipment to extract the water and dry the mess.

You should call this service immediately if you haven’t already!

Here are some tricks to get rid off that unpleasant smell after professionals have cleaned your carpet.

Hack #1

Baking soda

Baking soda is a natural, all-natural household cleaner that can be found in almost every DIY cleaning product. We warn you that baking soda can be tricky to use. You should be cautious if your carpet has long fibers.

Sprinkle some baking soda onto the carpet lightly. During this time, avoid walking on the carpet. The carpet should be vacuumed in the morning.

Hack #2

Vinegar

Vinegar can cut any smell and leave the object with a subtle, yet indefinable scent that is quite good. White vinegar can’t be mixed with any coloring or additives. Spray the mixture onto the carpet by mixing 1 part vinegar and 2 parts water in an aerosol bottle. You will be able to smell a new carpet the next morning after the water has dried overnight.

Hack #3

Alcohol

After you have chosen flood carpet cleaning, the best way to remove odors from carpets is with alcohol. You can also use rubbing alcohol to deodorize the carpet. The alcohol dries quicker and removes the bad smell quickly. Be careful when applying alcohol. You should be careful when applying alcohol to your carpet.

These are three easy and highly effective ways to leave your carpet odorless. All these hacks should be used with moderation. The solutions could cause damage to the carpet’s quality. Flood carpet cleaning should be rescheduled if the smell persists.